- Beranda
- The Lounge
ARTI CODE BEP PADA KOMPUTER
...
TS
choopersix
ARTI CODE BEP PADA KOMPUTER
Sebelumnya sori nih kalo salah kamar,ane cuman mau berbagi info aja,semoga bermanfaat....
sekali lagi sori kalo
Award
Award BIOSes typically use more screen errors than beep codes.
For Award BIOSes manufactured by Phoenix Technologies, note the following from the Phoenix Technologies AwardBIOS Error Messages page:
"The only AwardBIOS beep code indicates that a video error has occurred and the BIOS cannot initialize the video screen to display any additional information. This beep code consists of a single long beep followed by two short beeps. Any other beeps are probably RAM (Random Access Memory) problems."
Award BIOSes not manufactured under Phoenix Technologies use the following beeps; this information is from the BIOS Central Award BIOS Beep Codes page:
Beeps Meaning
1 long, 2 short Video adapter error: Bad or improperly seated video card
Repeating beeps Memory error: Bad or improperly seated RAM
1 long, 3 short Bad video RAM or video card not present
High-frequency beeps Overheated CPU: Check fans
Repeating high/low beeps CPU: Improperly seated or defective CPU
AMI (American Megatrends)
The information below is from the BIOS Central AMI BIOS Beep Codes page.
Beeps Meaning
1 short DRAM refresh failure
2 short Parity circuit failure in the first 64 KB of RAM: Likely a bad RAM IC, or possibly one of the hardware tests has failed
3 short Memory failure in the first 64 KB of RAM: Likely a bad RAM IC
4 short System timer failure: Bad clock IC or bad RAM in the first bank of memory
5 short Processor failure: The CPU has failed.
6 short Keyboard controller Gate A20 error: The keyboard controller has failed. Due to its integration into the system board, you usually must replace the motherboard.
7 short Virtual mode exception error: CPU has generated an exception error; bad CPU or motherboard
8 short Display memory Read/Write test failure: Bad video card
9 short ROM BIOS checksum failure: BIOS is defective
10 short CMOS shutdown Read/Write error
11 short Cache Memory error: Specifically, the L2 cache is bad.
1 long, 2 short Video system failure: Error in video card BIOS, or a horizontal retrace has failed
1 long, 3 short Conventional/Extended memory failure: RAM is bad
1 long, 8 short Display/Retrace test failed: Video adapter is defective or missing
AST BIOS
The following information is from the BIOS Central AST BIOS Beep Codes page.
Beeps Meaning
1 short CPU register test failure: The CPU has failed.
2 short Keyboard controller buffer failure: The keyboard controller has failed.
3 short Keyboard controller reset failure: The keyboard controller has failed or the motherboard circuitry is faulty.
4 short Keyboard communication failure: Bad keyboard controller or keyboard
5 short Keyboard input failure: The keyboard controller IC has failed.
6 short System board chipset failure: The chipset on the motherboard has failed. Replace the motherboard.
9 short BIOS ROM checksum error: The BIOS ROM has failed. If possible, replace the BIOS on the motherboard.
10 short System timer test failure: The system clock IC has failed.
11 short ASIC failure: Motherboard circuitry has failed. Replace the motherboard.
12 short CMOS RAM shutdown register failure: The real-time clock/CMOS IC failed. Replace the CMOS or motherboard.
1 long DMA controller 0 failure: The DMA controller IC for channel 0 has failed. If possible, replace the IC.
1 long, 1 short DMA controller 1 failure: The DMA controller IC for channel 1 has failed. If possible, replace the IC.
1 long, 2 short Video vertical retrace failure: The video adapter has probably failed. Replace the video adapter.
1 long, 3 short Video memory test failure: The video adapter's memory has failed. Replace the video adapter.
1 long, 4 short Video adapter failure: The video adapter has failed. Replace the video adapter.
1 long, 5 short 64 KB memory failure: A failure has occurred in the base 64 KB of memory. If possible, replace the RAM IC.
1 long, 6 short Unable to load interrupt vectors: The BIOS was unable to load the interrupt vectors into memory.
1 long, 7 short Unable to initialize video: This is a video problem. Replace the video adapter first. If the problem persists, replace the motherboard.
1 long, 8 short Video memory failure: There is a failure in the video memory. Replace the video adapter first. If the problem persists, replace the motherboard.
Compaq
The following information is from the BIOS Central Compaq BIOS Beep Codes page.
Beeps Meaning
1 short No error: The system is booting properly.
1 long, 1 short BIOS ROM checksum error: The contents of the BIOS ROM do not match the expected contents. If possible, reload the BIOS from the PAQ.
2 short General error: No specifics available on what this code means
1 long, 2 short Video error: Check the video adapter and make sure it's seated properly. If possible, replace the video adapter.
7 beeps (1 long, 1 short, 1 long, 1 short, pause, 1 long, 1 short, 1 short) AGP video: The AGP video card is faulty. Reseat the card or replace it outright. This beep pertains to Compaq Deskpro systems.
Continuous beep Memory error: Bad RAM; replace and test
1 short, 2 long Bad RAM: Reseat RAM, then retest; replace RAM if failure continues.
PHONIX
The following information applies to Phoenix BIOS Q3.07 or 4.x. This information is from the Phoenix BIOS beep codes section of the ComputerHope.com Computer POST and beep codes page.
Dashes indicate pauses between beeps.
Beeps Meaning
1-1-1-3 Verify real mode.
1-1-2-1 Get CPU type.
1-1-2-3 Initialize system hardware.
1-1-3-1 Initialize chipset registers with initial POST values.
1-1-3-2 Set in POST flag.
1-1-3-3 Initialize CPU registers.
1-1-4-1 Initialize cache to initial POST values.
1-1-4-3 Initialize I/O.
1-2-1-1 Initialize Power Management.
1-2-1-2 Load alternate registers with initial POST values.
1-2-1-3 Jump to UserPatch0.
1-2-2-1 Initialize keyboard controller.
1-2-2-3 BIOS ROM checksum
1-2-3-1 8254 timer initialization
1-2-3-3 8237 DMA controller initialization
1-2-4-1 Reset Programmable Interrupt Controller.
1-3-1-1 Test DRAM refresh.
1-3-1-3 Test 8742 Keyboard Controller.
1-3-2-1 Set ES segment to register to 4 GB.
1-3-3-1 28 Autosize DRAM.
1-3-3-3 Clear 512 KB base RAM.
1-3-4-1 Test 512 KB base address lines.
1-3-4-3 Test 512 KB base memory.
1-4-1-3 Test CPU bus-clock frequency.
1-4-2-4 Reinitialize the chipset.
1-4-3-1 Shadow system BIOS ROM.
1-4-3-2 Reinitialize the cache.
1-4-3-3 Autosize cache.
1-4-4-1 Configure advanced chipset registers.
1-4-4-2 Load alternate registers with CMOS values.
2-1-1-1 Set Initial CPU speed.
2-1-1-3 Initialize interrupt vectors.
2-1-2-1 Initialize BIOS interrupts.
2-1-2-3 Check ROM copyright notice.
2-1-2-4 Initialize manager for PCI Options ROMs.
2-1-3-1 Check video configuration against CMOS.
2-1-3-2 Initialize PCI bus and devices.
2-1-3-3 Initialize all video adapters in system.
2-1-4-1 Shadow video BIOS ROM.
2-1-4-3 Display copyright notice.
2-2-1-1 Display CPU type and speed.
2-2-1-3 Test keyboard.
2-2-2-1 Set key click if enabled.
2-2-2-3 56 Enable keyboard.
2-2-3-1 Test for unexpected interrupts.
2-2-3-3 Display message "Press F2 to enter SETUP".
2-2-4-1 Test RAM between 512 and 640 KB.
2-3-1-1 Test expanded memory.
2-3-1-3 Test extended memory address lines.
2-3-2-1 Jump to UserPatch1.
2-3-2-3 Configure advanced cache registers.
2-3-3-1 Enable external and CPU caches.
2-3-3-3 Display external cache size.
2-3-4-1 Display shadow message.
2-3-4-3 Display non-disposable segments.
2-4-1-1 Display error messages.
2-4-1-3 Check for configuration errors.
2-4-2-1 Test real-time clock.
2-4-2-3 Check for keyboard errors.
2-4-4-1 Set up hardware interrupts vectors.
2-4-4-3 Test coprocessor if present.
3-1-1-1 Disable onboard I/O ports.
3-1-1-3 Detect and install external RS232 ports.
3-1-2-1 Detect and install external parallel ports.
3-1-2-3 Re-initialize onboard I/O ports.
3-1-3-1 Initialize BIOS Data Area.
3-1-3-3 Initialize Extended BIOS Data Area.
3-1-4-1 Initialize floppy controller.
3-2-1-1 Initialize hard-disk controller.
3-2-1-2 Initialize local-bus hard-disk controller.
3-2-1-3 Jump to UserPatch2.
3-2-2-1 Disable A20 address line.
3-2-2-3 Clear huge ES segment register.
3-2-3-1 Search for option ROMs.
3-2-3-3 Shadow option ROMs.
3-2-4-1 Set up Power Management.
3-2-4-3 Enable hardware interrupts.
3-3-1-1 Set time of day.
3-3-1-3 Check key lock.
3-3-3-1 Erase "F2" message.
3-3-3-3 Scan for F2 keystroke.
3-3-4-1 Enter SETUP.
3-3-4-3 Clear in-POST flag.
3-4-1-1 Check for errors.
3-4-1-3 POST complete; prepare to boot operating system.
3-4-2-1 One beep.
3-4-2-3 Check password (optional).
3-4-3-1 Clear global descriptor table.
3-4-4-1 Clear parity checkers.
3-4-4-3 Clear screen (optional).
3-4-4-4 Check virus and backup reminders.
4-1-1-1 Try to boot with INT 19.
4-2-1-1 Interrupt handler error.
4-2-1-3 Unknown interrupt error.
4-2-2-1 Pending interrupt error.
4-2-2-3 Initialize option ROM error.
4-2-3-1 Shutdown error.
4-2-3-3 Extended Block Move.
4-2-4-1 Shutdown 10 error.
4-3-1-3 Initialize the chipset.
4-3-1-4 Initialize refresh counter.
4-3-2-1 Check for Forced Flash.
4-3-2-2 Check HW status of ROM.
4-3-2-3 BIOS ROM is okay.
4-3-2-4 Do a complete RAM test.
4-3-3-1 Do OEM initialization.
4-3-3-2 Initialize interrupt controller.
4-3-3-3 Read in bootstrap code.
4-3-3-4 Initialize all vectors.
4-3-4-1 Boot the Flash program.
4-3-4-2 Initialize the boot device.
4-3-4-3 Boot code was read okay.
IBM Desktop
Beeps Meaning
No beep No power, loose expansion card (ISA, PCI, or AGP), a short, or an improperly grounded motherboard
1 short System okay
1 long Video/display problem; video card incorrectly seated or defective
2 short POST Error displayed on monitor
3 long Problem with 3270 keyboard card
1 long, 1 short Problem with system board
1 long, 2 short Problem with display adapter (MDA, CGA)
1 long, 3 short Problem with EGA
Repeating short beeps Problem with power supply or system board
Continuous beep Problem with power supply or system board
IBM ThinkPad
Beeps Message
Continuous beeping System board failure
1 beep with blank display LCD connector problem, LCD backlight inverter failure, video adapter failure, or LCD assembly failure
1 beep w/message "Unable to access boot source" Boot device failure or bad system board
1 long, 2 short System board, video adapter, or LCD assembly failure
1 long, 4 short Low battery voltage
1 beep every second Low battery voltage
2 short w/message Read the error message on the display
2 short with blank display System board failure
Mylex
Beeps Meaning
1 Normal boot: No problems
2 Video adapter error: Video adapter is not seated or is faulty
3 Keyboard controller error: Keyboard controller IC bad
4 Keyboard error: Keyboard itself might be bad, or the controller IC on the motherboard
5 PIC 0 error: The programmable interrupt controller IC is bad
6 PIC 1 error: Same as above
7 DMA page register error: DMA controller IC is bad
8 RAM refresh error
9 RAM data error
10 RAM parity error
11 DMA controller 0 error: DMA controller IC for channel 0 has failed
12 CMOS RAM error: Bad CMOS RAM
13 DMA controller 1 error: DMA controller IC for channel 1 has failed
14 CMOS RAM battery error: Dead CMOS battery; can usually be replaced
15 CMOS RAM checksum error: CMOS RAM failed
16 BIOS ROM checksum error: BIOS RAM failed
Quadtel BIOS
The following information is from the BIOS Central Quadtel BIOS Beep Codes page.
1 short Normal boot: System is booting normally.
2 short CMOS IC error: The CMOS RAM is faulty. Replace the IC if possible.
1 long, 2 short Video failure: The video adapter is faulty. Reseat the video adapter or replace the adapter if possible.
1 long, 3 short Peripheral controller error: One or more of the system peripheral controllers is bad. Replace the controllers and retest.
EMBER
sekali lagi sori kalo
Award
Award BIOSes typically use more screen errors than beep codes.
For Award BIOSes manufactured by Phoenix Technologies, note the following from the Phoenix Technologies AwardBIOS Error Messages page:
"The only AwardBIOS beep code indicates that a video error has occurred and the BIOS cannot initialize the video screen to display any additional information. This beep code consists of a single long beep followed by two short beeps. Any other beeps are probably RAM (Random Access Memory) problems."
Award BIOSes not manufactured under Phoenix Technologies use the following beeps; this information is from the BIOS Central Award BIOS Beep Codes page:
Beeps Meaning
1 long, 2 short Video adapter error: Bad or improperly seated video card
Repeating beeps Memory error: Bad or improperly seated RAM
1 long, 3 short Bad video RAM or video card not present
High-frequency beeps Overheated CPU: Check fans
Repeating high/low beeps CPU: Improperly seated or defective CPU
AMI (American Megatrends)
The information below is from the BIOS Central AMI BIOS Beep Codes page.
Beeps Meaning
1 short DRAM refresh failure
2 short Parity circuit failure in the first 64 KB of RAM: Likely a bad RAM IC, or possibly one of the hardware tests has failed
3 short Memory failure in the first 64 KB of RAM: Likely a bad RAM IC
4 short System timer failure: Bad clock IC or bad RAM in the first bank of memory
5 short Processor failure: The CPU has failed.
6 short Keyboard controller Gate A20 error: The keyboard controller has failed. Due to its integration into the system board, you usually must replace the motherboard.
7 short Virtual mode exception error: CPU has generated an exception error; bad CPU or motherboard
8 short Display memory Read/Write test failure: Bad video card
9 short ROM BIOS checksum failure: BIOS is defective
10 short CMOS shutdown Read/Write error
11 short Cache Memory error: Specifically, the L2 cache is bad.
1 long, 2 short Video system failure: Error in video card BIOS, or a horizontal retrace has failed
1 long, 3 short Conventional/Extended memory failure: RAM is bad
1 long, 8 short Display/Retrace test failed: Video adapter is defective or missing
AST BIOS
The following information is from the BIOS Central AST BIOS Beep Codes page.
Beeps Meaning
1 short CPU register test failure: The CPU has failed.
2 short Keyboard controller buffer failure: The keyboard controller has failed.
3 short Keyboard controller reset failure: The keyboard controller has failed or the motherboard circuitry is faulty.
4 short Keyboard communication failure: Bad keyboard controller or keyboard
5 short Keyboard input failure: The keyboard controller IC has failed.
6 short System board chipset failure: The chipset on the motherboard has failed. Replace the motherboard.
9 short BIOS ROM checksum error: The BIOS ROM has failed. If possible, replace the BIOS on the motherboard.
10 short System timer test failure: The system clock IC has failed.
11 short ASIC failure: Motherboard circuitry has failed. Replace the motherboard.
12 short CMOS RAM shutdown register failure: The real-time clock/CMOS IC failed. Replace the CMOS or motherboard.
1 long DMA controller 0 failure: The DMA controller IC for channel 0 has failed. If possible, replace the IC.
1 long, 1 short DMA controller 1 failure: The DMA controller IC for channel 1 has failed. If possible, replace the IC.
1 long, 2 short Video vertical retrace failure: The video adapter has probably failed. Replace the video adapter.
1 long, 3 short Video memory test failure: The video adapter's memory has failed. Replace the video adapter.
1 long, 4 short Video adapter failure: The video adapter has failed. Replace the video adapter.
1 long, 5 short 64 KB memory failure: A failure has occurred in the base 64 KB of memory. If possible, replace the RAM IC.
1 long, 6 short Unable to load interrupt vectors: The BIOS was unable to load the interrupt vectors into memory.
1 long, 7 short Unable to initialize video: This is a video problem. Replace the video adapter first. If the problem persists, replace the motherboard.
1 long, 8 short Video memory failure: There is a failure in the video memory. Replace the video adapter first. If the problem persists, replace the motherboard.
Compaq
The following information is from the BIOS Central Compaq BIOS Beep Codes page.
Beeps Meaning
1 short No error: The system is booting properly.
1 long, 1 short BIOS ROM checksum error: The contents of the BIOS ROM do not match the expected contents. If possible, reload the BIOS from the PAQ.
2 short General error: No specifics available on what this code means
1 long, 2 short Video error: Check the video adapter and make sure it's seated properly. If possible, replace the video adapter.
7 beeps (1 long, 1 short, 1 long, 1 short, pause, 1 long, 1 short, 1 short) AGP video: The AGP video card is faulty. Reseat the card or replace it outright. This beep pertains to Compaq Deskpro systems.
Continuous beep Memory error: Bad RAM; replace and test
1 short, 2 long Bad RAM: Reseat RAM, then retest; replace RAM if failure continues.
PHONIX
The following information applies to Phoenix BIOS Q3.07 or 4.x. This information is from the Phoenix BIOS beep codes section of the ComputerHope.com Computer POST and beep codes page.
Dashes indicate pauses between beeps.
Beeps Meaning
1-1-1-3 Verify real mode.
1-1-2-1 Get CPU type.
1-1-2-3 Initialize system hardware.
1-1-3-1 Initialize chipset registers with initial POST values.
1-1-3-2 Set in POST flag.
1-1-3-3 Initialize CPU registers.
1-1-4-1 Initialize cache to initial POST values.
1-1-4-3 Initialize I/O.
1-2-1-1 Initialize Power Management.
1-2-1-2 Load alternate registers with initial POST values.
1-2-1-3 Jump to UserPatch0.
1-2-2-1 Initialize keyboard controller.
1-2-2-3 BIOS ROM checksum
1-2-3-1 8254 timer initialization
1-2-3-3 8237 DMA controller initialization
1-2-4-1 Reset Programmable Interrupt Controller.
1-3-1-1 Test DRAM refresh.
1-3-1-3 Test 8742 Keyboard Controller.
1-3-2-1 Set ES segment to register to 4 GB.
1-3-3-1 28 Autosize DRAM.
1-3-3-3 Clear 512 KB base RAM.
1-3-4-1 Test 512 KB base address lines.
1-3-4-3 Test 512 KB base memory.
1-4-1-3 Test CPU bus-clock frequency.
1-4-2-4 Reinitialize the chipset.
1-4-3-1 Shadow system BIOS ROM.
1-4-3-2 Reinitialize the cache.
1-4-3-3 Autosize cache.
1-4-4-1 Configure advanced chipset registers.
1-4-4-2 Load alternate registers with CMOS values.
2-1-1-1 Set Initial CPU speed.
2-1-1-3 Initialize interrupt vectors.
2-1-2-1 Initialize BIOS interrupts.
2-1-2-3 Check ROM copyright notice.
2-1-2-4 Initialize manager for PCI Options ROMs.
2-1-3-1 Check video configuration against CMOS.
2-1-3-2 Initialize PCI bus and devices.
2-1-3-3 Initialize all video adapters in system.
2-1-4-1 Shadow video BIOS ROM.
2-1-4-3 Display copyright notice.
2-2-1-1 Display CPU type and speed.
2-2-1-3 Test keyboard.
2-2-2-1 Set key click if enabled.
2-2-2-3 56 Enable keyboard.
2-2-3-1 Test for unexpected interrupts.
2-2-3-3 Display message "Press F2 to enter SETUP".
2-2-4-1 Test RAM between 512 and 640 KB.
2-3-1-1 Test expanded memory.
2-3-1-3 Test extended memory address lines.
2-3-2-1 Jump to UserPatch1.
2-3-2-3 Configure advanced cache registers.
2-3-3-1 Enable external and CPU caches.
2-3-3-3 Display external cache size.
2-3-4-1 Display shadow message.
2-3-4-3 Display non-disposable segments.
2-4-1-1 Display error messages.
2-4-1-3 Check for configuration errors.
2-4-2-1 Test real-time clock.
2-4-2-3 Check for keyboard errors.
2-4-4-1 Set up hardware interrupts vectors.
2-4-4-3 Test coprocessor if present.
3-1-1-1 Disable onboard I/O ports.
3-1-1-3 Detect and install external RS232 ports.
3-1-2-1 Detect and install external parallel ports.
3-1-2-3 Re-initialize onboard I/O ports.
3-1-3-1 Initialize BIOS Data Area.
3-1-3-3 Initialize Extended BIOS Data Area.
3-1-4-1 Initialize floppy controller.
3-2-1-1 Initialize hard-disk controller.
3-2-1-2 Initialize local-bus hard-disk controller.
3-2-1-3 Jump to UserPatch2.
3-2-2-1 Disable A20 address line.
3-2-2-3 Clear huge ES segment register.
3-2-3-1 Search for option ROMs.
3-2-3-3 Shadow option ROMs.
3-2-4-1 Set up Power Management.
3-2-4-3 Enable hardware interrupts.
3-3-1-1 Set time of day.
3-3-1-3 Check key lock.
3-3-3-1 Erase "F2" message.
3-3-3-3 Scan for F2 keystroke.
3-3-4-1 Enter SETUP.
3-3-4-3 Clear in-POST flag.
3-4-1-1 Check for errors.
3-4-1-3 POST complete; prepare to boot operating system.
3-4-2-1 One beep.
3-4-2-3 Check password (optional).
3-4-3-1 Clear global descriptor table.
3-4-4-1 Clear parity checkers.
3-4-4-3 Clear screen (optional).
3-4-4-4 Check virus and backup reminders.
4-1-1-1 Try to boot with INT 19.
4-2-1-1 Interrupt handler error.
4-2-1-3 Unknown interrupt error.
4-2-2-1 Pending interrupt error.
4-2-2-3 Initialize option ROM error.
4-2-3-1 Shutdown error.
4-2-3-3 Extended Block Move.
4-2-4-1 Shutdown 10 error.
4-3-1-3 Initialize the chipset.
4-3-1-4 Initialize refresh counter.
4-3-2-1 Check for Forced Flash.
4-3-2-2 Check HW status of ROM.
4-3-2-3 BIOS ROM is okay.
4-3-2-4 Do a complete RAM test.
4-3-3-1 Do OEM initialization.
4-3-3-2 Initialize interrupt controller.
4-3-3-3 Read in bootstrap code.
4-3-3-4 Initialize all vectors.
4-3-4-1 Boot the Flash program.
4-3-4-2 Initialize the boot device.
4-3-4-3 Boot code was read okay.
IBM Desktop
Beeps Meaning
No beep No power, loose expansion card (ISA, PCI, or AGP), a short, or an improperly grounded motherboard
1 short System okay
1 long Video/display problem; video card incorrectly seated or defective
2 short POST Error displayed on monitor
3 long Problem with 3270 keyboard card
1 long, 1 short Problem with system board
1 long, 2 short Problem with display adapter (MDA, CGA)
1 long, 3 short Problem with EGA
Repeating short beeps Problem with power supply or system board
Continuous beep Problem with power supply or system board
IBM ThinkPad
Beeps Message
Continuous beeping System board failure
1 beep with blank display LCD connector problem, LCD backlight inverter failure, video adapter failure, or LCD assembly failure
1 beep w/message "Unable to access boot source" Boot device failure or bad system board
1 long, 2 short System board, video adapter, or LCD assembly failure
1 long, 4 short Low battery voltage
1 beep every second Low battery voltage
2 short w/message Read the error message on the display
2 short with blank display System board failure
Mylex
Beeps Meaning
1 Normal boot: No problems
2 Video adapter error: Video adapter is not seated or is faulty
3 Keyboard controller error: Keyboard controller IC bad
4 Keyboard error: Keyboard itself might be bad, or the controller IC on the motherboard
5 PIC 0 error: The programmable interrupt controller IC is bad
6 PIC 1 error: Same as above
7 DMA page register error: DMA controller IC is bad
8 RAM refresh error
9 RAM data error
10 RAM parity error
11 DMA controller 0 error: DMA controller IC for channel 0 has failed
12 CMOS RAM error: Bad CMOS RAM
13 DMA controller 1 error: DMA controller IC for channel 1 has failed
14 CMOS RAM battery error: Dead CMOS battery; can usually be replaced
15 CMOS RAM checksum error: CMOS RAM failed
16 BIOS ROM checksum error: BIOS RAM failed
Quadtel BIOS
The following information is from the BIOS Central Quadtel BIOS Beep Codes page.
1 short Normal boot: System is booting normally.
2 short CMOS IC error: The CMOS RAM is faulty. Replace the IC if possible.
1 long, 2 short Video failure: The video adapter is faulty. Reseat the video adapter or replace the adapter if possible.
1 long, 3 short Peripheral controller error: One or more of the system peripheral controllers is bad. Replace the controllers and retest.
EMBER
zharki memberi reputasi
1
4.4K
19
Komentar yang asik ya
Mari bergabung, dapatkan informasi dan teman baru!
The Lounge
1.3MThread•105.3KAnggota
Tampilkan semua post
TS
choopersix
#1
INDONESIAN LANGUAGE By GOOGLE 
BIOS penghargaan biasanya menggunakan kesalahan layar lebih dari kode beep.
Untuk BIOS Penghargaan diproduksi oleh Phoenix Technologies, perhatikan hal berikut dari halaman Phoenix Technologies AwardBIOS Pesan Kesalahan:
"Satu-satunya kode bip AwardBIOS menunjukkan bahwa kesalahan telah terjadi dan video BIOS tidak dapat menginisialisasi layar video untuk menampilkan informasi tambahan. Ini kode bip terdiri dari bip panjang tunggal diikuti oleh dua beep pendek. Setiap beep lain mungkin RAM (Random Access Memory) masalah. "
BIOS penghargaan tidak diproduksi di bawah Phoenix Technologies menggunakan beep berikut; informasi ini dari Penghargaan halaman BIOS Tengah BIOS Beep Codes:
Beep Arti
1 panjang, 2 pendek Video adapter error: Bad video card atau tidak benar duduk
Mengulangi beep Memory error: Buruk atau tidak benar duduk RAM
1, 3 pendek video RAM Bad panjang atau video card tidak hadir
Beep frekuensi tinggi Kepanasan CPU: penggemar Periksa
Mengulangi tinggi / rendah beep CPU: Benar duduk atau cacat CPU
AMI (American Megatrends)
Berikut adalah informasi dari halaman BIOS Tengah AMI BIOS Beep Codes.
Beep Arti
1 pendek kegagalan refresh DRAM
2 kegagalan pendek Paritas sirkuit pertama 64 KB RAM: Kemungkinan buruk RAM IC, atau mungkin salah satu tes hardware telah gagal
3 kegagalan Memori pendek pertama 64 KB RAM: Kemungkinan buruk RAM IC
4 Sistem pendek Timer kegagalan: Bad jam IC atau RAM buruk di bank pertama memori
5 Prosesor rusak pendek: CPU telah gagal.
6 pengendali Gerbang kesalahan A20 Keyboard pendek: keyboard controller telah gagal. Karena integrasinya ke board sistem, Anda biasanya harus mengganti motherboard.
7 singkat Virtual modus pengecualian error: CPU telah menghasilkan kesalahan pengecualian; CPU buruk atau motherboard
Memori 8 Tampilan pendek Baca / Tulis kegagalan uji: video card Bad
9 pendek ROM BIOS checksum: BIOS yang rusak
10 shutdown yang pendek CMOS Baca / Tulis error
11 kesalahan Cache Memory singkat: Secara khusus, cache L2 yang buruk.
1 panjang, 2 pendek Video kegagalan sistem: Kesalahan dalam kartu video BIOS, atau menelusuri kembali horizontal telah gagal
1 panjang, 3 pendek Konvensional / kegagalan Extended memori: RAM buruk
1, 8 uji Tampilkan / menelusuri panjang pendek gagal: Video adapter rusak atau hilang
AST BIOS
Informasi berikut ini dari halaman BIOS Tengah AST BIOS Beep Codes.
Beep Arti
1 pendek CPU mendaftar kegagalan uji: CPU telah gagal.
2 pendek Keyboard kontroler kegagalan penyangga: keyboard controller telah gagal.
3 Keyboard kontroler kegagalan ulang pendek: keyboard controller telah gagal atau sirkuit motherboard rusak.
4 pendek kegagalan komunikasi Keyboard: Bad pengendali keyboard atau keyboard
5 pendek kegagalan masukan Keyboard: Keyboard IC controller telah gagal.
6 pendek Sistem papan kegagalan chipset: Chipset pada motherboard telah gagal. Mengganti motherboard.
9 pendek ROM BIOS checksum error: BIOS ROM telah gagal. Jika memungkinkan, ganti BIOS pada motherboard.
10 singkat Sistem Timer kegagalan uji: Sistem Jam IC telah gagal.
11 pendek ASIC kegagalan: Motherboard sirkuit telah gagal. Mengganti motherboard.
12 pendek CMOS shutdown yang mendaftar RAM Kegagalan: The real-time clock / CMOS IC gagal. Ganti CMOS atau motherboard.
1 panjang DMA controller 0 kegagalan: The DMA controller IC untuk kanal 0 telah gagal. Jika memungkinkan, ganti IC.
1 panjang, 1 pendek DMA controller 1 kegagalan: The DMA controller IC untuk kanal 1 telah gagal. Jika memungkinkan, ganti IC.
1 panjang, 2 pendek Video kegagalan menelusuri kembali vertikal: Adaptor video yang mungkin telah gagal. Ganti adaptor video.
1 panjang, 3 memori kegagalan tes pendek Video: Memori adaptor video telah gagal. Ganti adaptor video.
1 panjang, 4 kegagalan adaptor video pendek: Adaptor video telah gagal. Ganti adaptor video.
1 panjang, 5 pendek 64 KB memori kegagalan: Kegagalan telah terjadi di 64 KB memori dasar. Jika memungkinkan, ganti IC RAM.
1 panjang, 6 pendek Tidak dapat memuat vektor interupsi: BIOS tidak dapat memuat vektor interrupt ke memori.
1 panjang, 7 singkat Tidak dapat menginisialisasi Video: Ini adalah masalah video. Ganti adaptor video pertama. Jika masalah berlanjut, ganti motherboard.
1, 8 kegagalan memori pendek Video panjang: Ada kegagalan dalam memori video. Ganti adaptor video pertama. Jika masalah berlanjut, ganti motherboard.
Compaq
Informasi berikut ini dari halaman BIOS Tengah Compaq BIOS Beep Codes.
Beep Arti
1 pendek ada error: Sistem ini boot dengan benar.
1 panjang, 1 pendek ROM BIOS checksum error: Isi ROM BIOS tidak cocok dengan isi yang diharapkan. Jika memungkinkan, reload BIOS dari PAQ tersebut.
2 pendek Kesalahan Umum: Tidak spesifik tersedia pada apa kode ini berarti
1 panjang, 2 pendek Video kesalahan: Periksa adaptor video dan pastikan itu duduk dengan benar. Jika memungkinkan, ganti adaptor video.
7 beep (1 panjang, 1 pendek, 1 panjang, 1 pendek, pause, 1 panjang, 1 pendek, 1 pendek) AGP Video: AGP kartu video rusak. Pasang kembali kartu atau menggantinya langsung. Bip ini berkaitan dengan Compaq Deskpro sistem.
Kontinyu bip Memory error: Bad RAM, mengganti dan menguji
1 pendek, panjang 2 Bad RAM: Pasang RAM, kemudian tes ulang, ganti RAM jika gagal terus.
PHONIX
Informasi berikut berlaku untuk Phoenix BIOS Q3.07 atau 4.x. Informasi ini dari Phoenix BIOS beep kode bagian dari ComputerHope.com POST Komputer dan halaman kode beep.
Tanda hubung menunjukkan jeda antara beep.
Beep Arti
1-1-1-3 Verifikasi modus real.
Dapatkan 1-1-2-1 jenis CPU.
1-1-2-3 Menginisialisasi perangkat keras sistem.
1-1-3-1 Initialize chipset register dengan nilai-nilai POST awal.
1-1-3-2 Set dalam bendera POST.
1-1-3-3 register CPU Initialize.
1-1-4-1 Inisialisasi cache nilai POST awal.
1-1-4-3 Inisialisasi I / O.
1-2-1-1 Initialize Power Management.
1-2-1-2 Beban register alternatif dengan nilai-nilai POST awal.
1-2-1-3 Langsung ke UserPatch0.
1-2-2-1 Menginisialisasi keyboard controller.
1-2-2-3 BIOS ROM checksum
1-2-3-1 8254 waktu inisialisasi
1-2-3-3 8237 DMA controller inisialisasi
1-2-4-1 ulang Programmable Interrupt Controller.
1-3-1-1 Uji DRAM menyegarkan.
1-3-1-3 Uji 8742 Keyboard Controller.
1-3-2-1 Set segmen ES mendaftar untuk 4 GB.
1-3-3-1 28 AutoSize DRAM.
1-3-3-3 Batal 512 KB basis RAM.
1-3-4-1 Uji 512 KB dasar baris alamat.
1-3-4-3 Uji 512 KB memori dasar.
1-4-1-3 Uji CPU bus-frekuensi clock.
1-4-2-4 reinitialize chipset.
1-4-3-1 Bayangan sistem BIOS ROM.
1-4-3-2 reinitialize cache.
1-4-3-3 AutoSize Cache.
1-4-4-1 Konfigurasi register chipset canggih.
1-4-4-2 Beban register alternatif dengan nilai-nilai CMOS.
2-1-1-1 Set awal kecepatan CPU.
2-1-1-3 Inisialisasi vektor interupsi.
2-1-2-1 Inisialisasi interupsi BIOS.
2-1-2-3 Periksa ROM pemberitahuan hak cipta.
2-1-2-4 Initialize manajer untuk PCI Pilihan ROM.
2-1-3-1 Periksa konfigurasi video terhadap CMOS.
2-1-3-2 Initialize PCI bus dan perangkat.
2-1-3-3 Inisialisasi semua adapter video dalam sistem.
2-1-4-1 Bayangan Video BIOS ROM.
2-1-4-3 Tampilan pemberitahuan hak cipta.
2-2-1-1 Tampilan jenis dan kecepatan CPU.
2-2-1-3 Uji Keyboard.
2-2-2-1 Set tombol klik jika diaktifkan.
2-2-2-3 56 Aktifkan Keyboard.
2-2-3-1 uji interupsi tak terduga.
2-2-3-3 Tampilan pesan "Tekan F2 untuk masuk ke SETUP".
2-2-4-1 Uji RAM antara 512 dan 640 KB.
2-3-1-1 Uji memori diperluas.
2-3-1-3 Uji diperpanjang baris alamat memori.
2-3-2-1 Langsung ke UserPatch1.
2-3-2-3 Konfigurasi register cache yang canggih.
2-3-3-1 Aktifkan cache eksternal dan CPU.
2-3-3-3 Tampilan ukuran cache eksternal.
2-3-4-1 Tampilan pesan bayangan.
2-3-4-3 Tampilan segmen non-sekali pakai.
2-4-1-1 Tampilan pesan kesalahan.
2-4-1-3 Periksa kesalahan konfigurasi.
2-4-2-1 Uji real-time clock.
2-4-2-3 Periksa kesalahan Keyboard.
2-4-4-1 Set up vektor interupsi perangkat keras.
2-4-4-3 Uji coprocessor jika ada.
3-1-1-1 Nonaktifkan onboard I / O port.
3-1-1-3 Mendeteksi dan menginstal RS232 port eksternal.
3-1-2-1 Mendeteksi dan menginstal port paralel eksternal.
3-1-2-3 Re-menginisialisasi onboard I / O port.
3-1-3-1 Inisialisasi BIOS data area.
3-1-3-3 Inisialisasi Diperpanjang BIOS data area.
3-1-4-1 Inisialisasi pengontrol floppy.
3-2-1-1 Inisialisasi hard-disk controller.
3-2-1-2 Inisialisasi lokal-bus hard-disk controller.
3-2-1-3 Langsung ke UserPatch2.
3-2-2-1 Nonaktifkan baris alamat A20.
3-2-2-3 Batal segmen ES besar mendaftar.
3-2-3-1 Cari ROM pilihan.
3-2-3-3 Bayangan pilihan ROM.
3-2-4-1 Mengatur Power Management.
3-2-4-3 Aktifkan interupsi perangkat keras.
3-3-1-1 Set waktu.
3-3-1-3 Periksa kunci tombol.
3-3-3-1 Erase "F2" pesan.
3-3-3-3 Pindai keystroke F2.
3-3-4-1 Masukkan SETUP.
3-3-4-3 Batal bendera di-POST.
3-4-1-1 Periksa kesalahan.
3-4-1-3 POST lengkap; mempersiapkan diri untuk boot sistem operasi.
3-4-2-1 Satu bip.
3-4-2-3 Periksa sandi (opsional).
3-4-3-1 Hapus tabel deskripsi global.
3-4-4-1 Batal paritas catur.
3-4-4-3 Hapus layar (opsional).
3-4-4-4 Periksa virus dan pengingat cadangan.
4-1-1-1 Cobalah untuk boot dengan INT 19.
4-2-1-1 Interrupt penanganan error.
4-2-1-3 diketahui kesalahan interupsi.
4-2-2-1 Tertunda interupsi kesalahan.
4-2-2-3 Inisialisasi pilihan galat ROM.
4-2-3-1 kesalahan Shutdown.
4-2-3-3 Perpanjangan Blok Pindah.
4-2-4-1 Shutdown 10 kesalahan.
4-3-1-3 Inisialisasi chipset.
4-3-1-4 Initialize menyegarkan kontra.
4-3-2-1 Periksa Paksa Flash.
4-3-2-2 Periksa status HW ROM.
4-3-2-3 BIOS ROM tidak apa-apa.
4-3-2-4 Lakukan tes RAM lengkap.
4-3-3-1 Apakah OEM inisialisasi.
4-3-3-2 Inisialisasi interrupt controller.
4-3-3-3 Baca dalam kode bootstrap.
4-3-3-4 Inisialisasi semua vektor.
4-3-4-1 Boot program Flash.
4-3-4-2 Inisialisasi perangkat boot.
4-3-4-3 kode Boot dibacakan oke.
IBM Desktop
Beep Arti
Tidak bip ada daya, kartu ekspansi longgar (ISA, PCI, atau AGP), pendek, atau motherboard tidak benar membumi
1 Sistem pendek oke
1 Video / display masalah lama, kartu video tidak terpasang dengan benar atau rusak
2 Kesalahan POST pendek ditampilkan pada monitor
3 Masalah panjang dengan 3270 kartu Keyboard
1 panjang, 1 pendek Masalah dengan board sistem
1 panjang, 2 pendek Masalah dengan adaptor display (MDA, CGA)
1 panjang, 3 pendek Masalah dengan EGA
Mengulangi beep pendek masalah dengan power supply atau board sistem
Bip Masalah terus menerus dengan power supply atau board sistem
IBM ThinkPad
Beep Pesan
Sistem bip kegagalan papan kontinyu
1 bip dengan layar LCD masalah konektor kosong, LCD backlight inverter kegagalan, kegagalan video adapter, atau kegagalan perakitan LCD
1 bip w / pesan "Tidak dapat mengakses sumber booting" Boot kegagalan perangkat atau papan sistem yang buruk
1 panjang, 2 pendek papan System, video adapter, atau LCD kegagalan perakitan
1 panjang, 4 pendek tegangan baterai rendah
1 beep setiap detik tegangan baterai rendah
2 pesan w / singkat Baca pesan kesalahan pada layar
2 pendek dengan Sistem layar kosong kegagalan papan
Mylex
Beep Arti
1 normal boot: Tidak ada masalah
2 Video adapter error: Video adapter tidak duduk atau rusak
3 pengontrol keyboard error: Keyboard IC controller buruk
4 Keyboard error: Keyboard sendiri mungkin buruk, atau IC controller di motherboard
5 PIC 0 error: The diprogram interupsi IC controller buruk
6 PIC 1 error: Sama seperti di atas
7 DMA mendaftar halaman error: DMA controller IC buruk
8 refresh RAM kesalahan
9 RAM data error
10 RAM kesalahan paritas
11 DMA controller 0 error: DMA controller IC untuk kanal 0 telah gagal
12 CMOS RAM error: Bad CMOS RAM
13 DMA controller 1 error: DMA controller IC untuk kanal 1 telah gagal
14 CMOS RAM baterai error: baterai CMOS mati, biasanya dapat diganti
15 CMOS checksum error RAM: CMOS RAM gagal
16 BIOS ROM checksum error: RAM BIOS gagal
Quadtel BIOS
Informasi berikut ini dari halaman BIOS Tengah Quadtel BIOS Beep Codes.
1 pendek booting normal: Sistem booting secara normal.
2 pendek CMOS IC error: RAM CMOS rusak. Ganti IC jika memungkinkan.
1 panjang, 2 pendek Video kegagalan: Adaptor video rusak. Ulangi pemasangan adaptor video atau mengganti adaptor jika memungkinkan.
1 panjang, 3 pendek Peripheral kontroler kesalahan: Satu atau lebih pengendali perifer sistem yang buruk. Ganti kontroler dan tes ulang.
BIOS penghargaan biasanya menggunakan kesalahan layar lebih dari kode beep.
Untuk BIOS Penghargaan diproduksi oleh Phoenix Technologies, perhatikan hal berikut dari halaman Phoenix Technologies AwardBIOS Pesan Kesalahan:
"Satu-satunya kode bip AwardBIOS menunjukkan bahwa kesalahan telah terjadi dan video BIOS tidak dapat menginisialisasi layar video untuk menampilkan informasi tambahan. Ini kode bip terdiri dari bip panjang tunggal diikuti oleh dua beep pendek. Setiap beep lain mungkin RAM (Random Access Memory) masalah. "
BIOS penghargaan tidak diproduksi di bawah Phoenix Technologies menggunakan beep berikut; informasi ini dari Penghargaan halaman BIOS Tengah BIOS Beep Codes:
Beep Arti
1 panjang, 2 pendek Video adapter error: Bad video card atau tidak benar duduk
Mengulangi beep Memory error: Buruk atau tidak benar duduk RAM
1, 3 pendek video RAM Bad panjang atau video card tidak hadir
Beep frekuensi tinggi Kepanasan CPU: penggemar Periksa
Mengulangi tinggi / rendah beep CPU: Benar duduk atau cacat CPU
AMI (American Megatrends)
Berikut adalah informasi dari halaman BIOS Tengah AMI BIOS Beep Codes.
Beep Arti
1 pendek kegagalan refresh DRAM
2 kegagalan pendek Paritas sirkuit pertama 64 KB RAM: Kemungkinan buruk RAM IC, atau mungkin salah satu tes hardware telah gagal
3 kegagalan Memori pendek pertama 64 KB RAM: Kemungkinan buruk RAM IC
4 Sistem pendek Timer kegagalan: Bad jam IC atau RAM buruk di bank pertama memori
5 Prosesor rusak pendek: CPU telah gagal.
6 pengendali Gerbang kesalahan A20 Keyboard pendek: keyboard controller telah gagal. Karena integrasinya ke board sistem, Anda biasanya harus mengganti motherboard.
7 singkat Virtual modus pengecualian error: CPU telah menghasilkan kesalahan pengecualian; CPU buruk atau motherboard
Memori 8 Tampilan pendek Baca / Tulis kegagalan uji: video card Bad
9 pendek ROM BIOS checksum: BIOS yang rusak
10 shutdown yang pendek CMOS Baca / Tulis error
11 kesalahan Cache Memory singkat: Secara khusus, cache L2 yang buruk.
1 panjang, 2 pendek Video kegagalan sistem: Kesalahan dalam kartu video BIOS, atau menelusuri kembali horizontal telah gagal
1 panjang, 3 pendek Konvensional / kegagalan Extended memori: RAM buruk
1, 8 uji Tampilkan / menelusuri panjang pendek gagal: Video adapter rusak atau hilang
AST BIOS
Informasi berikut ini dari halaman BIOS Tengah AST BIOS Beep Codes.
Beep Arti
1 pendek CPU mendaftar kegagalan uji: CPU telah gagal.
2 pendek Keyboard kontroler kegagalan penyangga: keyboard controller telah gagal.
3 Keyboard kontroler kegagalan ulang pendek: keyboard controller telah gagal atau sirkuit motherboard rusak.
4 pendek kegagalan komunikasi Keyboard: Bad pengendali keyboard atau keyboard
5 pendek kegagalan masukan Keyboard: Keyboard IC controller telah gagal.
6 pendek Sistem papan kegagalan chipset: Chipset pada motherboard telah gagal. Mengganti motherboard.
9 pendek ROM BIOS checksum error: BIOS ROM telah gagal. Jika memungkinkan, ganti BIOS pada motherboard.
10 singkat Sistem Timer kegagalan uji: Sistem Jam IC telah gagal.
11 pendek ASIC kegagalan: Motherboard sirkuit telah gagal. Mengganti motherboard.
12 pendek CMOS shutdown yang mendaftar RAM Kegagalan: The real-time clock / CMOS IC gagal. Ganti CMOS atau motherboard.
1 panjang DMA controller 0 kegagalan: The DMA controller IC untuk kanal 0 telah gagal. Jika memungkinkan, ganti IC.
1 panjang, 1 pendek DMA controller 1 kegagalan: The DMA controller IC untuk kanal 1 telah gagal. Jika memungkinkan, ganti IC.
1 panjang, 2 pendek Video kegagalan menelusuri kembali vertikal: Adaptor video yang mungkin telah gagal. Ganti adaptor video.
1 panjang, 3 memori kegagalan tes pendek Video: Memori adaptor video telah gagal. Ganti adaptor video.
1 panjang, 4 kegagalan adaptor video pendek: Adaptor video telah gagal. Ganti adaptor video.
1 panjang, 5 pendek 64 KB memori kegagalan: Kegagalan telah terjadi di 64 KB memori dasar. Jika memungkinkan, ganti IC RAM.
1 panjang, 6 pendek Tidak dapat memuat vektor interupsi: BIOS tidak dapat memuat vektor interrupt ke memori.
1 panjang, 7 singkat Tidak dapat menginisialisasi Video: Ini adalah masalah video. Ganti adaptor video pertama. Jika masalah berlanjut, ganti motherboard.
1, 8 kegagalan memori pendek Video panjang: Ada kegagalan dalam memori video. Ganti adaptor video pertama. Jika masalah berlanjut, ganti motherboard.
Compaq
Informasi berikut ini dari halaman BIOS Tengah Compaq BIOS Beep Codes.
Beep Arti
1 pendek ada error: Sistem ini boot dengan benar.
1 panjang, 1 pendek ROM BIOS checksum error: Isi ROM BIOS tidak cocok dengan isi yang diharapkan. Jika memungkinkan, reload BIOS dari PAQ tersebut.
2 pendek Kesalahan Umum: Tidak spesifik tersedia pada apa kode ini berarti
1 panjang, 2 pendek Video kesalahan: Periksa adaptor video dan pastikan itu duduk dengan benar. Jika memungkinkan, ganti adaptor video.
7 beep (1 panjang, 1 pendek, 1 panjang, 1 pendek, pause, 1 panjang, 1 pendek, 1 pendek) AGP Video: AGP kartu video rusak. Pasang kembali kartu atau menggantinya langsung. Bip ini berkaitan dengan Compaq Deskpro sistem.
Kontinyu bip Memory error: Bad RAM, mengganti dan menguji
1 pendek, panjang 2 Bad RAM: Pasang RAM, kemudian tes ulang, ganti RAM jika gagal terus.
PHONIX
Informasi berikut berlaku untuk Phoenix BIOS Q3.07 atau 4.x. Informasi ini dari Phoenix BIOS beep kode bagian dari ComputerHope.com POST Komputer dan halaman kode beep.
Tanda hubung menunjukkan jeda antara beep.
Beep Arti
1-1-1-3 Verifikasi modus real.
Dapatkan 1-1-2-1 jenis CPU.
1-1-2-3 Menginisialisasi perangkat keras sistem.
1-1-3-1 Initialize chipset register dengan nilai-nilai POST awal.
1-1-3-2 Set dalam bendera POST.
1-1-3-3 register CPU Initialize.
1-1-4-1 Inisialisasi cache nilai POST awal.
1-1-4-3 Inisialisasi I / O.
1-2-1-1 Initialize Power Management.
1-2-1-2 Beban register alternatif dengan nilai-nilai POST awal.
1-2-1-3 Langsung ke UserPatch0.
1-2-2-1 Menginisialisasi keyboard controller.
1-2-2-3 BIOS ROM checksum
1-2-3-1 8254 waktu inisialisasi
1-2-3-3 8237 DMA controller inisialisasi
1-2-4-1 ulang Programmable Interrupt Controller.
1-3-1-1 Uji DRAM menyegarkan.
1-3-1-3 Uji 8742 Keyboard Controller.
1-3-2-1 Set segmen ES mendaftar untuk 4 GB.
1-3-3-1 28 AutoSize DRAM.
1-3-3-3 Batal 512 KB basis RAM.
1-3-4-1 Uji 512 KB dasar baris alamat.
1-3-4-3 Uji 512 KB memori dasar.
1-4-1-3 Uji CPU bus-frekuensi clock.
1-4-2-4 reinitialize chipset.
1-4-3-1 Bayangan sistem BIOS ROM.
1-4-3-2 reinitialize cache.
1-4-3-3 AutoSize Cache.
1-4-4-1 Konfigurasi register chipset canggih.
1-4-4-2 Beban register alternatif dengan nilai-nilai CMOS.
2-1-1-1 Set awal kecepatan CPU.
2-1-1-3 Inisialisasi vektor interupsi.
2-1-2-1 Inisialisasi interupsi BIOS.
2-1-2-3 Periksa ROM pemberitahuan hak cipta.
2-1-2-4 Initialize manajer untuk PCI Pilihan ROM.
2-1-3-1 Periksa konfigurasi video terhadap CMOS.
2-1-3-2 Initialize PCI bus dan perangkat.
2-1-3-3 Inisialisasi semua adapter video dalam sistem.
2-1-4-1 Bayangan Video BIOS ROM.
2-1-4-3 Tampilan pemberitahuan hak cipta.
2-2-1-1 Tampilan jenis dan kecepatan CPU.
2-2-1-3 Uji Keyboard.
2-2-2-1 Set tombol klik jika diaktifkan.
2-2-2-3 56 Aktifkan Keyboard.
2-2-3-1 uji interupsi tak terduga.
2-2-3-3 Tampilan pesan "Tekan F2 untuk masuk ke SETUP".
2-2-4-1 Uji RAM antara 512 dan 640 KB.
2-3-1-1 Uji memori diperluas.
2-3-1-3 Uji diperpanjang baris alamat memori.
2-3-2-1 Langsung ke UserPatch1.
2-3-2-3 Konfigurasi register cache yang canggih.
2-3-3-1 Aktifkan cache eksternal dan CPU.
2-3-3-3 Tampilan ukuran cache eksternal.
2-3-4-1 Tampilan pesan bayangan.
2-3-4-3 Tampilan segmen non-sekali pakai.
2-4-1-1 Tampilan pesan kesalahan.
2-4-1-3 Periksa kesalahan konfigurasi.
2-4-2-1 Uji real-time clock.
2-4-2-3 Periksa kesalahan Keyboard.
2-4-4-1 Set up vektor interupsi perangkat keras.
2-4-4-3 Uji coprocessor jika ada.
3-1-1-1 Nonaktifkan onboard I / O port.
3-1-1-3 Mendeteksi dan menginstal RS232 port eksternal.
3-1-2-1 Mendeteksi dan menginstal port paralel eksternal.
3-1-2-3 Re-menginisialisasi onboard I / O port.
3-1-3-1 Inisialisasi BIOS data area.
3-1-3-3 Inisialisasi Diperpanjang BIOS data area.
3-1-4-1 Inisialisasi pengontrol floppy.
3-2-1-1 Inisialisasi hard-disk controller.
3-2-1-2 Inisialisasi lokal-bus hard-disk controller.
3-2-1-3 Langsung ke UserPatch2.
3-2-2-1 Nonaktifkan baris alamat A20.
3-2-2-3 Batal segmen ES besar mendaftar.
3-2-3-1 Cari ROM pilihan.
3-2-3-3 Bayangan pilihan ROM.
3-2-4-1 Mengatur Power Management.
3-2-4-3 Aktifkan interupsi perangkat keras.
3-3-1-1 Set waktu.
3-3-1-3 Periksa kunci tombol.
3-3-3-1 Erase "F2" pesan.
3-3-3-3 Pindai keystroke F2.
3-3-4-1 Masukkan SETUP.
3-3-4-3 Batal bendera di-POST.
3-4-1-1 Periksa kesalahan.
3-4-1-3 POST lengkap; mempersiapkan diri untuk boot sistem operasi.
3-4-2-1 Satu bip.
3-4-2-3 Periksa sandi (opsional).
3-4-3-1 Hapus tabel deskripsi global.
3-4-4-1 Batal paritas catur.
3-4-4-3 Hapus layar (opsional).
3-4-4-4 Periksa virus dan pengingat cadangan.
4-1-1-1 Cobalah untuk boot dengan INT 19.
4-2-1-1 Interrupt penanganan error.
4-2-1-3 diketahui kesalahan interupsi.
4-2-2-1 Tertunda interupsi kesalahan.
4-2-2-3 Inisialisasi pilihan galat ROM.
4-2-3-1 kesalahan Shutdown.
4-2-3-3 Perpanjangan Blok Pindah.
4-2-4-1 Shutdown 10 kesalahan.
4-3-1-3 Inisialisasi chipset.
4-3-1-4 Initialize menyegarkan kontra.
4-3-2-1 Periksa Paksa Flash.
4-3-2-2 Periksa status HW ROM.
4-3-2-3 BIOS ROM tidak apa-apa.
4-3-2-4 Lakukan tes RAM lengkap.
4-3-3-1 Apakah OEM inisialisasi.
4-3-3-2 Inisialisasi interrupt controller.
4-3-3-3 Baca dalam kode bootstrap.
4-3-3-4 Inisialisasi semua vektor.
4-3-4-1 Boot program Flash.
4-3-4-2 Inisialisasi perangkat boot.
4-3-4-3 kode Boot dibacakan oke.
IBM Desktop
Beep Arti
Tidak bip ada daya, kartu ekspansi longgar (ISA, PCI, atau AGP), pendek, atau motherboard tidak benar membumi
1 Sistem pendek oke
1 Video / display masalah lama, kartu video tidak terpasang dengan benar atau rusak
2 Kesalahan POST pendek ditampilkan pada monitor
3 Masalah panjang dengan 3270 kartu Keyboard
1 panjang, 1 pendek Masalah dengan board sistem
1 panjang, 2 pendek Masalah dengan adaptor display (MDA, CGA)
1 panjang, 3 pendek Masalah dengan EGA
Mengulangi beep pendek masalah dengan power supply atau board sistem
Bip Masalah terus menerus dengan power supply atau board sistem
IBM ThinkPad
Beep Pesan
Sistem bip kegagalan papan kontinyu
1 bip dengan layar LCD masalah konektor kosong, LCD backlight inverter kegagalan, kegagalan video adapter, atau kegagalan perakitan LCD
1 bip w / pesan "Tidak dapat mengakses sumber booting" Boot kegagalan perangkat atau papan sistem yang buruk
1 panjang, 2 pendek papan System, video adapter, atau LCD kegagalan perakitan
1 panjang, 4 pendek tegangan baterai rendah
1 beep setiap detik tegangan baterai rendah
2 pesan w / singkat Baca pesan kesalahan pada layar
2 pendek dengan Sistem layar kosong kegagalan papan
Mylex
Beep Arti
1 normal boot: Tidak ada masalah
2 Video adapter error: Video adapter tidak duduk atau rusak
3 pengontrol keyboard error: Keyboard IC controller buruk
4 Keyboard error: Keyboard sendiri mungkin buruk, atau IC controller di motherboard
5 PIC 0 error: The diprogram interupsi IC controller buruk
6 PIC 1 error: Sama seperti di atas
7 DMA mendaftar halaman error: DMA controller IC buruk
8 refresh RAM kesalahan
9 RAM data error
10 RAM kesalahan paritas
11 DMA controller 0 error: DMA controller IC untuk kanal 0 telah gagal
12 CMOS RAM error: Bad CMOS RAM
13 DMA controller 1 error: DMA controller IC untuk kanal 1 telah gagal
14 CMOS RAM baterai error: baterai CMOS mati, biasanya dapat diganti
15 CMOS checksum error RAM: CMOS RAM gagal
16 BIOS ROM checksum error: RAM BIOS gagal
Quadtel BIOS
Informasi berikut ini dari halaman BIOS Tengah Quadtel BIOS Beep Codes.
1 pendek booting normal: Sistem booting secara normal.
2 pendek CMOS IC error: RAM CMOS rusak. Ganti IC jika memungkinkan.
1 panjang, 2 pendek Video kegagalan: Adaptor video rusak. Ulangi pemasangan adaptor video atau mengganti adaptor jika memungkinkan.
1 panjang, 3 pendek Peripheral kontroler kesalahan: Satu atau lebih pengendali perifer sistem yang buruk. Ganti kontroler dan tes ulang.
Diubah oleh choopersix 23-06-2013 23:11
zharki memberi reputasi
1