- Beranda
- The Lounge
Assault Rifle Caliber
...
TS
semionstrogov32
Assault Rifle Caliber
Halo agan agan kali ini TS akan menampilkan peluru senapan serbu yang memiliki karakteristik tersendiri
1. 5,45x39mm
Jadi peluru yang digunakan AK-74 ini menjadi momok bagi pasukan Mujahidin pas perang Afghanistan (1979-1989) karena peluru ini diciptakan untuk merobek jaringan tubuh manusia menurut pihak Barat.
2. 5,56x45mm NATO
The 5.56×45mm NATO (official NATO nomenclature 5.56 NATO) is an intermediate cartridge developed in the United States and originally chambered in the M16 rifle. Under STANAG 4172, it is a standard cartridge for NATO forces as well as many non-NATO countries.[3] It is derived from, but is not identical to, the .223 Remington cartridge.
Peluru standar NATO untuk senapan serbu ini memiliki daya rusak yang bagus untuk jarak dekat dan menengah tapi buruk untuk jarak jauh (1000 meter (tergantung jenis peluru yang dipakai Marksman Rifle 5,56mm NATO)).
Sumber :Wikipedia
TS akan mengupdate thread ini setelah istirahat selesai
Update
3.7,62x39mm
The 7.62×39mm round is a rifle cartridge of Soviet origin that was designed during World War II. It was first used in the RPD. Due to the worldwide proliferation of the SKS and AK-47 pattern rifles, the cartridge is used by both militaries and civilians alike. 7.62×39mm ammunition is purportedly tested to function well in temperatures ranging from −50 to 50 °C (−58 to 122 °F) cementing its usefulness in cold polar or hot desert conditions.
The 7.62×39mm cartridge was influenced by a variety of foreign developments, including the German Mkb 42(H) and the U.S. M1 carbine.[3]
Shortly after the war, the world's most widespread military-pattern rifle was designed for this cartridge: the AK-47. The cartridge remained the Soviet standard until the 1970s, and is still one of the most common intermediate rifle cartridges used around the world. It was replaced in Russian service by the 5.45×39mm cartridge, which is used by the current-issue AK-74 and its variants.
On July 15, 1943, the Technical Council of the People's Commissariat for Armaments (Russian: Техсовет Наркомата Вооружения) met to discuss the introduction of a Soviet intermediate cartridge. The Soviet planners also decided at this meeting that their new cartridge be used in a whole range of infantry weapons, including a semi-automatic carbine, a selective fire (assault) rifle, and a light machine gun. The job of designing the Soviet intermediate cartridge was assigned to a committee led by chief designer NM Elizarov (Н.М. Елизаров), assisted by PV Ryazanov (П.В. Рязанов), BV Semin (Б.В. Семин) and IT Melnikov (И.Т. Мельников). Elizarov collaborated closely with some leading weapons designers, including Fedorov, Tokarev, Simonov, and Shpagin. About 314 cartridge designs were considered theoretically, before narrowing the selection down to 8 models that were physically constructed and tested.[3] Most of the development work on the new cartridge took place at OKB-44, which was soon thereafter renamed as NII-44, and which in 1949 was merged with NII-61, itself merged with TsNIITochmash in 1966.[4]
A first variant of the new cartridge was officially adopted for service after completing range trials in December 1943; it was given the GRAU index 57-N-231. This cartridge actually had a case length of 41 mm, so it is sometimes referred to as the 7.62×41. The bullet it contained was 22.8 mm long and had a core made entirely of lead. This bullet has a somewhat stubbier appearance than later 7.62×39 bullets, with its maximal radius being attained after only 13.01 mm from its tip, and it was lacking a boat tail. After some further refinements, a pilot production series of this cartridge began in March 1944.[4]
After more detailed testing results became available, starting in 1944 the cartridge was tweaked in order to improve its accuracy and penetration. Initially, the boat tail had been omitted because the Soviet designers had assumed (incorrectly) that it would only make a difference at long ranges, when the bullet became subsonic, and the accuracy of the intermediate cartridge at these ranges was considered inconsequential. However, further testing showed that the boat tail improved accuracy even at shorter ranges, where the bullet was still supersonic. In order to maintain the overall mass of the bullet, after adding the boat tail, the ogival head section of the bullet was lengthened as well, making the bullet more streamlined overall. The maximum radius was now attained at some 15.95 mm from the tip and the overall length of the bullet increased to 26.8 mm. In order to preserve the total length of the cartridge, the case sleeve was shortened to 38.7 mm (and by rounding it is customarily referred to as 7.62×39.) Additionally, the new bullet had a core made of low-carbon steel wrapped in lead. The use of low-carbon (mild) steel was guided mostly by the desire to reuse some industrial equipment that was manufacturing the 7.62×25mm Tokarev cartridge rather than by bullet fragmentation considerations. This bullet was given the acronym "7.62 PS" (76.2 ПС). The "S" initially stood for "surrogate" (суррогатированная, surrogatirovannaya), but later the letter was taken to refer to the steel component (стальной, stal'noy) of the core, which accounted for about 50% of the core volume. The 7.62×39 cartridge equipped with the PS bullet finally overcame all objections of the GAU in mid-1947, when it was ordered into series production, and given the index 57-N-231S.[4]
The design that was ultimately selected by the Soviets has more dimensional similarities to the GECO cartridge used in the Vollmer M35 than with the Polte round used by the later German Sturmgewehr. Some authors, including C. J. Chivers, have speculated that the Soviets may have had access to the works of GECO and Vollmer during 1940, when Hitler allowed a large number of Soviet engineers to tour various German armament factories.[5] Anthony Williams however argues that the Soviet M43 round was so different that it was possible to dismiss the idea that it was a copy of any German round in existence at the time.[6]
The 57-N-231S cartridge used a "bimetallic" (steel and copper) case. In the early 1960s, a "lacquered" steel case was introduced, and the new cartridge was initially given the designation 57-N-231SL. In an effort to simplify terminology, sometime thereafter the 57-N-231 designation was recycled to denote all steel-core 7.62×39 Soviet ammunition, irrespective of case build.[4]
In the mid 1950s, Elizarov's team, now working at NII-61, developed a special subsonic bullet for the 7.62×39 cartridge. It was adopted for service in 1962, and given the army designation "7.62 US" (US stood for уменьшенной скоростью, meaning "reduced speed") and the GRAU index 57-N-231U. The subsonic bullet was considerably longer (33.62 mm) and heavier (12.5 g) than the PS bullet, and also had a different, non-layered core structure. The core of its head section was entirely made of tool steel, followed by another section entirely made of lead. The subsonic bullet also has a larger maximum diameter of 7.94 mm compared to all other 7.62×39 bullets that peak at 7.92 mm diameter; the larger diameter of the lead-core section was intended to provide a tighter fit to the barrel by better engaging the rifling grooves. The 7.62 subsonic ammo was intended to be fired from AK-47-type rifles equipped with the PBS-1 silencer, and developed a muzzle velocity of about 285–300 m/s. For recognition, this ammo typically has the bullet tips painted black with green band underneath.[4]
After 1989, the regular (PS) Russian bullets started to be manufactured with a steel core with a higher carbon concentration and subjected to heat treatment. This change improved their penetration by 1.5–2 times. It is not possible to externally distinguish these bullets from the earlier, softer PS ones except by year of fabrication. At about the same time, tool steel was adopted for a normal velocity 7.62×39 bullet. Called BP, this bullet was developed in the 1980s and 1990s. It was officially adopted for Russian service in 2002 under the service name "7.62 BP", and with the GRAU designation 7N23. The BP bullet is claimed to achieve over three times the penetration of the PS bullet; it can defeat the Russian bullet-proof vest with designation 6B5 at distances below 250 meters. The BP cartridge has the tip of its bullet painted black. The BP bullet itself is slightly longer (27.4 mm) compared to the PS bullet, but has the same mass of 7.9 grams.[4]
At the same 1943 meeting that decided the development new cartridge, the Soviet planners decided that a whole range of new small arms should use it, including a semi-automatic carbine, a fully automatic rifle, and a light machine gun. Design contests for these new weapons began in earnest in 1944.[3]
Peluru AK-47, AKM serta RPD dan RPK ini memiliki daya rusak yang cukup dahsyat pada jarak dekat tapi pada jarah menengah sampai jauh (600-1000 meter) daya rusaknya berkurang.
Ojo lali dan
Ojo kasih
1. 5,45x39mm
Spoiler for 5,45x39mm:
Spoiler for Pendahuluan:
The 5.45×39mm cartridge is a rimless bottlenecked rifle cartridge. It was introduced into service in 1974 by the Soviet Union for use with the new AK-74 assault rifle. It gradually supplemented, then largely replaced the 7.62×39mm round in servic
Spoiler for Sejarah:
The 5.45×39mm cartridge was developed in the early 1970s by a group of Soviet designers and engineers under the direction of M. Sabelnikov. Further group members were: L. I. Bulavsky, B. B. Semin, M. E. Fedorov, P. F. Sazonov, V. Volkov, V. A. Nikolaev, E. E. Zimin and P. S. Korolev.
The 5.45×39mm is an example of an international tendency towards relatively small-sized, lightweight, high-velocity military service cartridges. Cartridges like the 5.45×39mm, 5.56×45mm NATO and Chinese 5.8×42mm allow a soldier to carry more ammunition for the same weight compared to their larger and heavier predecessor cartridges, have favourable maximum point-blank range or "battle zero" characteristics and produce relatively low bolt thrust and free recoil impulse, favouring lightweight arms design and automatic fire accuracy.[2]
The Soviet original military issue 7N6 cartridge variant introduced in 1974 are loaded with full metal jacket bullets that have a somewhat complex construction. The 3.43 g (52.9 gr) boat-tail projectile's jacket is clad in gilding metal. The unhardened 1.43 g (22.1 gr) steel (steel 10) rod penetrator core is covered by a thin lead inlay which does not fill the entire point end, leaving a hollow cavity inside the nose. The bullet is cut to length during the manufacturing process to give the correct weight. The 7N6 uses a boat-tail design to reduce drag and there is a small lead plug crimped in place in the base of the bullet. The lead plug, in combination with the air space at the point of the bullet, has the effect of moving the bullet's center of gravity to the rear; the hollow air space also makes the bullet's point prone to deformation when the bullet strikes anything solid, inducing yaw. The brown-lacquered steel case is Berdan primed. Its 39.37 mm (1.55 in) length makes it slightly longer than the 7.62×39mm case which measures exactly 38.60 mm (1.52 in). The primer has a copper cup and is sealed with a heavy red lacquer. The propellant charge is a ball powder with similar burning characteristics to the WC844 powder used in 5.56×45mm NATO ammunition. The 7N6 cartridge weight is 10.75 g (165.9 gr).
Tests indicate the free recoil energy delivered by the 5.45×39mm AK-74 assault rifle is 3.39 J (2.50 ft·lb), compared to 6.44 J (4.75 ft·lb) delivered by the 5.56×45mm NATO in the M16 assault rifle and 7.19 J (5.30 ft·lb) delivered by the 7.62×39mm in the AKM assault rifle.[3]
Military 5.45×39mm ammunition was produced in the former Soviet Union, GDR and Yugoslavia, and is produced in Bulgaria, Poland and Romania. In the former Soviet Union this ammunition is produced in Russia, Kyrgyzstan, Uzbekistan and Ukraine.
The 5.45×39mm is an example of an international tendency towards relatively small-sized, lightweight, high-velocity military service cartridges. Cartridges like the 5.45×39mm, 5.56×45mm NATO and Chinese 5.8×42mm allow a soldier to carry more ammunition for the same weight compared to their larger and heavier predecessor cartridges, have favourable maximum point-blank range or "battle zero" characteristics and produce relatively low bolt thrust and free recoil impulse, favouring lightweight arms design and automatic fire accuracy.[2]
The Soviet original military issue 7N6 cartridge variant introduced in 1974 are loaded with full metal jacket bullets that have a somewhat complex construction. The 3.43 g (52.9 gr) boat-tail projectile's jacket is clad in gilding metal. The unhardened 1.43 g (22.1 gr) steel (steel 10) rod penetrator core is covered by a thin lead inlay which does not fill the entire point end, leaving a hollow cavity inside the nose. The bullet is cut to length during the manufacturing process to give the correct weight. The 7N6 uses a boat-tail design to reduce drag and there is a small lead plug crimped in place in the base of the bullet. The lead plug, in combination with the air space at the point of the bullet, has the effect of moving the bullet's center of gravity to the rear; the hollow air space also makes the bullet's point prone to deformation when the bullet strikes anything solid, inducing yaw. The brown-lacquered steel case is Berdan primed. Its 39.37 mm (1.55 in) length makes it slightly longer than the 7.62×39mm case which measures exactly 38.60 mm (1.52 in). The primer has a copper cup and is sealed with a heavy red lacquer. The propellant charge is a ball powder with similar burning characteristics to the WC844 powder used in 5.56×45mm NATO ammunition. The 7N6 cartridge weight is 10.75 g (165.9 gr).
Tests indicate the free recoil energy delivered by the 5.45×39mm AK-74 assault rifle is 3.39 J (2.50 ft·lb), compared to 6.44 J (4.75 ft·lb) delivered by the 5.56×45mm NATO in the M16 assault rifle and 7.19 J (5.30 ft·lb) delivered by the 7.62×39mm in the AKM assault rifle.[3]
Military 5.45×39mm ammunition was produced in the former Soviet Union, GDR and Yugoslavia, and is produced in Bulgaria, Poland and Romania. In the former Soviet Union this ammunition is produced in Russia, Kyrgyzstan, Uzbekistan and Ukraine.
Spoiler for Efek Kerusakan yang ditimbulkan:
Early ballistics tests demonstrated a pronounced tumbling effect with high speed cameras.[5] Some Western authorities believed this bullet was designed to tumble in flesh to increase wounding potential. At the time, it was believed that yawing and cavitation of projectiles were primarily responsible for tissue damage. Martin Fackler conducted a study with an AK-74 assault rifle using live pigs and ballistic gelatin; "The result of our preset test indicate that the AK-74 bullet acts in the manner expected of a full-metal-cased military ammunition - it does not deform or fragment when striking soft tissues".[6] Most organs and tissue were too flexible to be severely damaged by the temporary cavity effect caused by yaw and cavitation of a projectile. With the 5.45 mm bullet, tumbling produced a temporary cavity twice, at depths of 100 mm (3.9 in) and 350 mm (13.8 in). This is similar to (but more rapid than) modern 7.62×39mm ammunition and to (non-fragmenting) 5.56 mm ammunition.
Military 5.45×39mm rounds offer better penetration over (fragmenting) military 5.56×45mm NATO rounds.[7][8] However, unlike its 5.56mm counterpart, the 5.45mm round “does not deform or fragment when striking soft tissues.”[7][8] Nevertheless, during the Afghan war the Mujahedeen called the 5.45×39mm round the "Poison Bullet" due to the severe wounds it produced to extremities and the resulting need to amputate.[9][10][11
Military 5.45×39mm rounds offer better penetration over (fragmenting) military 5.56×45mm NATO rounds.[7][8] However, unlike its 5.56mm counterpart, the 5.45mm round “does not deform or fragment when striking soft tissues.”[7][8] Nevertheless, during the Afghan war the Mujahedeen called the 5.45×39mm round the "Poison Bullet" due to the severe wounds it produced to extremities and the resulting need to amputate.[9][10][11
Jadi peluru yang digunakan AK-74 ini menjadi momok bagi pasukan Mujahidin pas perang Afghanistan (1979-1989) karena peluru ini diciptakan untuk merobek jaringan tubuh manusia menurut pihak Barat.
2. 5,56x45mm NATO
Spoiler for 5,56x45mm NATO:
The 5.56×45mm NATO (official NATO nomenclature 5.56 NATO) is an intermediate cartridge developed in the United States and originally chambered in the M16 rifle. Under STANAG 4172, it is a standard cartridge for NATO forces as well as many non-NATO countries.[3] It is derived from, but is not identical to, the .223 Remington cartridge.
Spoiler for History:
In the 1950s, the 7.62×51mm NATO rifle cartridge (physically interchangeable with, but not identical to, the .308 Winchester rifle cartridge)[4] was selected to replace the .30-06 Springfield as the standard NATO rifle cartridge. At the time of selection, there had been criticism that the 7.62×51mm NATO was too powerful for lightweight modern service rifles, causing excessive recoil, and that as a result it did not allow for sufficient automatic rate of fire from hand-held weapons in modern combat.[citation needed]
The British had extensive evidence with their own experimentation with intermediate cartridges since 1945 and were on the point of adopting a .280 inch (7 mm) cartridge when the selection of the 7.62×51mm NATO was made. The FN company had also been involved in the development of the .280 round including developing a version of the FN FAL in .280.[5] The concerns about recoil and effectiveness were effectively overruled by the US within NATO, and the other NATO nations accepted that standardization was more important at the time than selection of the ideal cartridge. However, while the 7.62×51mm NATO round became NATO standard, the US was already engaged in research of their own, which ultimately led to the 5.56×45mm NATO cartridge.[citation needed]
During the late 1950s, ArmaLite and other U.S. firearm designers started their individual Small Caliber/High Velocity (SCHV) rifle experiments using the commercial .222 Remington cartridge. When it became clear that there was not enough powder capacity to meet U.S. Continental Army Command's (CONARC) velocity and penetration requirements, ArmaLite contacted Remington to create a similar cartridge with a longer case body and shorter neck. This became the .222 Remington Special. At the same time, Springfield Armory's Earle Harvey had Remington create an even longer cartridge case then known as the .224 Springfield. Springfield was forced to drop out of the CONARC competition, and thus the .224 Springfield was later released as a commercial sporting cartridge known as the .222 Remington Magnum. To prevent confusion among all of the competing .222 cartridge designations, the .222 Remington Special was renamed the .223 Remington. With the U.S. military adoption of the M16 rifle in 1963, the .223 Remington was standardized as the 5.56×45mm NATO. As a commercial sporting cartridge the .223 Remington was introduced in 1964.
The 5.56×45mm cartridge, along with the M16 rifle, were initially adopted by U.S. infantry forces as interim solutions to address the weight and control issues experienced with the 7.62×51mm round and M14 rifle. In the late 1950s, the Special Purpose Individual Weapon program sought to create flechette rounds to allow troops to fire sabot-type projectiles to give a short flight time and flat trajectory with a muzzle velocity of 1,200 metres per second (3,900 ft/s) to 1,500 metres per second (4,900 ft/s). At those speeds, factors like range, wind drift, and target movement would no longer affect performance. Several manufacturers produced varying weapons designs, including traditional wooden, bullpup, "space age," and even multi-barrel designs with drum magazines. All used similar ammunition firing a 1.8 mm diameter dart with a plastic "puller" sabot filling the case mouth. While the flechette ammo had excellent armor penetration, there were doubts about their terminal effectiveness against unprotected targets. Conventional cased ammunition was more accurate and the sabots were expensive to produce. The SPIW never created a weapons system that was combat effective, so the M16 was retained, and the 5.56 mm round was kept as the standard U.S. infantry rifle cartridge.[5]
In 1977, NATO members signed an agreement to select a second, smaller caliber cartridge to replace the 7.62×51mm NATO cartridge.[8] Of the cartridges tendered, the 5.56×45mm NATO was successful, but not the 55 gr M193 round used by the U.S. at that time. Instead, the Belgian 62 gr SS109 round was chosen for standardization. The SS109 used a heavier bullet with a seven grain steel core for better penetration against lightly armored targets,specifically to meet a requirement that the bullet be able to penetrate through one side of a steel helmet at 600 meters. It had a slightly lower muzzle velocity but better long-range performance. This requirement made the SS109 (M855) round less capable of fragmentation than the M193 and was considered more humane.[9]
The 5.56×45mm NATO inspired an international tendency towards relatively small-sized, lightweight, high-velocity military service cartridges that produce relatively low bolt thrust and free recoil impulse, favoring lightweight arms design and automatic fire accuracy. Similar intermediate cartridges were developed and introduced by the Soviet Union in 1974 (5.45×39mm) and by the People's Republic of China in 1987 (5.8×42mm).[5][10]
The British had extensive evidence with their own experimentation with intermediate cartridges since 1945 and were on the point of adopting a .280 inch (7 mm) cartridge when the selection of the 7.62×51mm NATO was made. The FN company had also been involved in the development of the .280 round including developing a version of the FN FAL in .280.[5] The concerns about recoil and effectiveness were effectively overruled by the US within NATO, and the other NATO nations accepted that standardization was more important at the time than selection of the ideal cartridge. However, while the 7.62×51mm NATO round became NATO standard, the US was already engaged in research of their own, which ultimately led to the 5.56×45mm NATO cartridge.[citation needed]
During the late 1950s, ArmaLite and other U.S. firearm designers started their individual Small Caliber/High Velocity (SCHV) rifle experiments using the commercial .222 Remington cartridge. When it became clear that there was not enough powder capacity to meet U.S. Continental Army Command's (CONARC) velocity and penetration requirements, ArmaLite contacted Remington to create a similar cartridge with a longer case body and shorter neck. This became the .222 Remington Special. At the same time, Springfield Armory's Earle Harvey had Remington create an even longer cartridge case then known as the .224 Springfield. Springfield was forced to drop out of the CONARC competition, and thus the .224 Springfield was later released as a commercial sporting cartridge known as the .222 Remington Magnum. To prevent confusion among all of the competing .222 cartridge designations, the .222 Remington Special was renamed the .223 Remington. With the U.S. military adoption of the M16 rifle in 1963, the .223 Remington was standardized as the 5.56×45mm NATO. As a commercial sporting cartridge the .223 Remington was introduced in 1964.
The 5.56×45mm cartridge, along with the M16 rifle, were initially adopted by U.S. infantry forces as interim solutions to address the weight and control issues experienced with the 7.62×51mm round and M14 rifle. In the late 1950s, the Special Purpose Individual Weapon program sought to create flechette rounds to allow troops to fire sabot-type projectiles to give a short flight time and flat trajectory with a muzzle velocity of 1,200 metres per second (3,900 ft/s) to 1,500 metres per second (4,900 ft/s). At those speeds, factors like range, wind drift, and target movement would no longer affect performance. Several manufacturers produced varying weapons designs, including traditional wooden, bullpup, "space age," and even multi-barrel designs with drum magazines. All used similar ammunition firing a 1.8 mm diameter dart with a plastic "puller" sabot filling the case mouth. While the flechette ammo had excellent armor penetration, there were doubts about their terminal effectiveness against unprotected targets. Conventional cased ammunition was more accurate and the sabots were expensive to produce. The SPIW never created a weapons system that was combat effective, so the M16 was retained, and the 5.56 mm round was kept as the standard U.S. infantry rifle cartridge.[5]
In 1977, NATO members signed an agreement to select a second, smaller caliber cartridge to replace the 7.62×51mm NATO cartridge.[8] Of the cartridges tendered, the 5.56×45mm NATO was successful, but not the 55 gr M193 round used by the U.S. at that time. Instead, the Belgian 62 gr SS109 round was chosen for standardization. The SS109 used a heavier bullet with a seven grain steel core for better penetration against lightly armored targets,specifically to meet a requirement that the bullet be able to penetrate through one side of a steel helmet at 600 meters. It had a slightly lower muzzle velocity but better long-range performance. This requirement made the SS109 (M855) round less capable of fragmentation than the M193 and was considered more humane.[9]
The 5.56×45mm NATO inspired an international tendency towards relatively small-sized, lightweight, high-velocity military service cartridges that produce relatively low bolt thrust and free recoil impulse, favoring lightweight arms design and automatic fire accuracy. Similar intermediate cartridges were developed and introduced by the Soviet Union in 1974 (5.45×39mm) and by the People's Republic of China in 1987 (5.8×42mm).[5][10]
Peluru standar NATO untuk senapan serbu ini memiliki daya rusak yang bagus untuk jarak dekat dan menengah tapi buruk untuk jarak jauh (1000 meter (tergantung jenis peluru yang dipakai Marksman Rifle 5,56mm NATO)).
Sumber :Wikipedia
TS akan mengupdate thread ini setelah istirahat selesai
Update
3.7,62x39mm
Spoiler for 7,62x39mm:
The 7.62×39mm round is a rifle cartridge of Soviet origin that was designed during World War II. It was first used in the RPD. Due to the worldwide proliferation of the SKS and AK-47 pattern rifles, the cartridge is used by both militaries and civilians alike. 7.62×39mm ammunition is purportedly tested to function well in temperatures ranging from −50 to 50 °C (−58 to 122 °F) cementing its usefulness in cold polar or hot desert conditions.
The 7.62×39mm cartridge was influenced by a variety of foreign developments, including the German Mkb 42(H) and the U.S. M1 carbine.[3]
Shortly after the war, the world's most widespread military-pattern rifle was designed for this cartridge: the AK-47. The cartridge remained the Soviet standard until the 1970s, and is still one of the most common intermediate rifle cartridges used around the world. It was replaced in Russian service by the 5.45×39mm cartridge, which is used by the current-issue AK-74 and its variants.
On July 15, 1943, the Technical Council of the People's Commissariat for Armaments (Russian: Техсовет Наркомата Вооружения) met to discuss the introduction of a Soviet intermediate cartridge. The Soviet planners also decided at this meeting that their new cartridge be used in a whole range of infantry weapons, including a semi-automatic carbine, a selective fire (assault) rifle, and a light machine gun. The job of designing the Soviet intermediate cartridge was assigned to a committee led by chief designer NM Elizarov (Н.М. Елизаров), assisted by PV Ryazanov (П.В. Рязанов), BV Semin (Б.В. Семин) and IT Melnikov (И.Т. Мельников). Elizarov collaborated closely with some leading weapons designers, including Fedorov, Tokarev, Simonov, and Shpagin. About 314 cartridge designs were considered theoretically, before narrowing the selection down to 8 models that were physically constructed and tested.[3] Most of the development work on the new cartridge took place at OKB-44, which was soon thereafter renamed as NII-44, and which in 1949 was merged with NII-61, itself merged with TsNIITochmash in 1966.[4]
A first variant of the new cartridge was officially adopted for service after completing range trials in December 1943; it was given the GRAU index 57-N-231. This cartridge actually had a case length of 41 mm, so it is sometimes referred to as the 7.62×41. The bullet it contained was 22.8 mm long and had a core made entirely of lead. This bullet has a somewhat stubbier appearance than later 7.62×39 bullets, with its maximal radius being attained after only 13.01 mm from its tip, and it was lacking a boat tail. After some further refinements, a pilot production series of this cartridge began in March 1944.[4]
After more detailed testing results became available, starting in 1944 the cartridge was tweaked in order to improve its accuracy and penetration. Initially, the boat tail had been omitted because the Soviet designers had assumed (incorrectly) that it would only make a difference at long ranges, when the bullet became subsonic, and the accuracy of the intermediate cartridge at these ranges was considered inconsequential. However, further testing showed that the boat tail improved accuracy even at shorter ranges, where the bullet was still supersonic. In order to maintain the overall mass of the bullet, after adding the boat tail, the ogival head section of the bullet was lengthened as well, making the bullet more streamlined overall. The maximum radius was now attained at some 15.95 mm from the tip and the overall length of the bullet increased to 26.8 mm. In order to preserve the total length of the cartridge, the case sleeve was shortened to 38.7 mm (and by rounding it is customarily referred to as 7.62×39.) Additionally, the new bullet had a core made of low-carbon steel wrapped in lead. The use of low-carbon (mild) steel was guided mostly by the desire to reuse some industrial equipment that was manufacturing the 7.62×25mm Tokarev cartridge rather than by bullet fragmentation considerations. This bullet was given the acronym "7.62 PS" (76.2 ПС). The "S" initially stood for "surrogate" (суррогатированная, surrogatirovannaya), but later the letter was taken to refer to the steel component (стальной, stal'noy) of the core, which accounted for about 50% of the core volume. The 7.62×39 cartridge equipped with the PS bullet finally overcame all objections of the GAU in mid-1947, when it was ordered into series production, and given the index 57-N-231S.[4]
The design that was ultimately selected by the Soviets has more dimensional similarities to the GECO cartridge used in the Vollmer M35 than with the Polte round used by the later German Sturmgewehr. Some authors, including C. J. Chivers, have speculated that the Soviets may have had access to the works of GECO and Vollmer during 1940, when Hitler allowed a large number of Soviet engineers to tour various German armament factories.[5] Anthony Williams however argues that the Soviet M43 round was so different that it was possible to dismiss the idea that it was a copy of any German round in existence at the time.[6]
The 57-N-231S cartridge used a "bimetallic" (steel and copper) case. In the early 1960s, a "lacquered" steel case was introduced, and the new cartridge was initially given the designation 57-N-231SL. In an effort to simplify terminology, sometime thereafter the 57-N-231 designation was recycled to denote all steel-core 7.62×39 Soviet ammunition, irrespective of case build.[4]
In the mid 1950s, Elizarov's team, now working at NII-61, developed a special subsonic bullet for the 7.62×39 cartridge. It was adopted for service in 1962, and given the army designation "7.62 US" (US stood for уменьшенной скоростью, meaning "reduced speed") and the GRAU index 57-N-231U. The subsonic bullet was considerably longer (33.62 mm) and heavier (12.5 g) than the PS bullet, and also had a different, non-layered core structure. The core of its head section was entirely made of tool steel, followed by another section entirely made of lead. The subsonic bullet also has a larger maximum diameter of 7.94 mm compared to all other 7.62×39 bullets that peak at 7.92 mm diameter; the larger diameter of the lead-core section was intended to provide a tighter fit to the barrel by better engaging the rifling grooves. The 7.62 subsonic ammo was intended to be fired from AK-47-type rifles equipped with the PBS-1 silencer, and developed a muzzle velocity of about 285–300 m/s. For recognition, this ammo typically has the bullet tips painted black with green band underneath.[4]
After 1989, the regular (PS) Russian bullets started to be manufactured with a steel core with a higher carbon concentration and subjected to heat treatment. This change improved their penetration by 1.5–2 times. It is not possible to externally distinguish these bullets from the earlier, softer PS ones except by year of fabrication. At about the same time, tool steel was adopted for a normal velocity 7.62×39 bullet. Called BP, this bullet was developed in the 1980s and 1990s. It was officially adopted for Russian service in 2002 under the service name "7.62 BP", and with the GRAU designation 7N23. The BP bullet is claimed to achieve over three times the penetration of the PS bullet; it can defeat the Russian bullet-proof vest with designation 6B5 at distances below 250 meters. The BP cartridge has the tip of its bullet painted black. The BP bullet itself is slightly longer (27.4 mm) compared to the PS bullet, but has the same mass of 7.9 grams.[4]
At the same 1943 meeting that decided the development new cartridge, the Soviet planners decided that a whole range of new small arms should use it, including a semi-automatic carbine, a fully automatic rifle, and a light machine gun. Design contests for these new weapons began in earnest in 1944.[3]
Peluru AK-47, AKM serta RPD dan RPK ini memiliki daya rusak yang cukup dahsyat pada jarak dekat tapi pada jarah menengah sampai jauh (600-1000 meter) daya rusaknya berkurang.
Ojo lali dan
Ojo kasih
Diubah oleh semionstrogov32 09-09-2016 06:16
0
5.5K
Kutip
48
Balasan
Komentar yang asik ya
Mari bergabung, dapatkan informasi dan teman baru!
The Lounge
923.4KThread•84.5KAnggota
Urutkan
Terlama
Komentar yang asik ya