Cara membuat miniature motor dari jam tangan bekas
TS
Asscaron
Cara membuat miniature motor dari jam tangan bekas
Sebelumnya assalamualaikum dulu nih agan agan.. barusan ane iseng iseng nyari thread di kaskus tentang miniature motor tapi ane liat kok ga ada tutorialnya ya?
di thread ane yg ke3 ini ane mau share tutorialnya.. cuma 13 step aja
Spoiler for video:
atau yg kagak kuat buffer ni ada gambar langkahnya
Spoiler for step 1:
Make two wheels and the tires. For this step you will need two watches.
Remove the watch faces from the bands.
Wrap a band around a watch face. Check it for fit.
Glue the watchband around the watch face.
Repeat so that you have two wheels with tires.
Spoiler for step 2:
Make the cylinders. For this part you will need two flexible watchbands.
Remove the bands from the watch faces.
Wrap the band around in a flattish circle shape and glue it.
Leave the cylinders to dry sitting on the end of a peg/ clothes pin. This will help keep their shape.
Spoiler for step 3:
Make the engine. For this part you will need two watch faces and the cylinders made in the previous step.
Place glue over the watch face.
Press down the other watch face onto the face with glue on it (face to face).
Add glue to the side of the dried cylinders.
Press each cylinder onto the side of the "engine", right next to each other (see image).
Spoiler for step 4:
Create the fender. For this step you will need two stiff watchbands.
Remove the bands from a watch with a stiff metallic band. On one side, however, leave half of the band intact still.
Add glue to the inner side of the stiff band (see image).
Glue two small metal tabs on the underside that will sit on the tire. Add glue to these small pieces (see image).
Glue the fender to each tire.
Spoiler for step 5:
Make the petrol/ gas tank. For this step, you will need a watch with a flexible band and a rectangular or square shaped watchface and watch backing.
Pull the back out of a square/rectangular watch.
Spread glue on the back.
Glue the back onto the watch back from which it was removed (see image). Ensure that the watch piece still has a band attached either side.
Spoiler for step 6:
Make the steering wheel. This step picks up using the watch as glued from the previous step.
Push a small sturdy copper wire piece through one end of the watch where the flexible band meets with the watch (see image).
Bend the wire into handlebar shapes. Make sure that one of the watchbands has been snapped off most of the way. Adjust the handlebar until it sits well. You might need to use pliers in this step (and the following step).
Spoiler for step 7:
Bend another piece of sturdy copper wire into a U shape as shown in the image. SPOILER]
[SPOILER=step 8]Gather all the pieces you have made in ready for assembling the bike. Make sure that everything is in the position as shown in this image and that all pieces are dry and sturdy.
Spoiler for step 9:
Build the bike. Using the pieces assembled above, make sure that everything will fit in place easily prior to gluing by mock assembling without glue. Now is the time to make any necessary adjustments before following the gluing steps that follow. Here are the checks to make:
Push the back wheel toward the engine. Wrap a small part of the band still attached to the back wheel over the cylinder.
Push in the front wheel to the engine and bring down the handlebar section to the engine as well.
Bring the light to the front of the handlebars. Use an old watch battery for this piece.
Bring the U-shaped piece to the back of the bike to sit on the fender as the backrest of the bike seat.
Spoiler for step 10:
Glue each piece into place. Once you are certain that all the pieces fit well and you have made any adjustments necessary, it is time to put the bike together with glue. Follow the images and video carefully here.
Glue the back wheel to the cylinder.
Glue the back rest to the back wheel fender.
Glue the handlebar/gas tank piece to the front wheel fender.
Glue the battery "light" to the piece extending down from the handlebar to the front wheel fender.
Glue the front of the bike to the unglued cylinder (the back of the bike is already attached to the other cylinder).
Spoiler for step 11:
Thread small wire covers over the handlebars. Small plastic tubing used to cover electrical wires is best, or you could wrap black tape around if preferred. These make the holding pads of the handlebars.
Spoiler for step 12:
Add a metal pen. This serves as the exhaust pipe.
Shave the paint off the pen (if needed).
Check the positioning of the pen.
Glue the pen into place.
Spoiler for step 13:
Check the completed glued-together bike miniature. Make any adjustments as needed.
itu tutorial lengkap cara buat miniature motor sederhana gan. maaf kalo tutorialnya bahasa inggris soalnya ane ga jago ngartiin bahasa inggris. hehe
ni ane udah nyoba tapi ga mirip di tutorial karna bahan terbatas.
Spoiler for karya ane:
Sekian dulu dari ane.. kalo agan suka ane ga nolak kok.. hehe
Diubah oleh Asscaron 02-10-2014 06:11
0
5K
Kutip
12
Balasan
Komentar yang asik ya
Mari bergabung, dapatkan informasi dan teman baru!